PA 1000Цитата:
Сообщение от mohov_a
Вид для печати
PA 1000Цитата:
Сообщение от mohov_a
Нет! Надо смотреть инструкцию! Какая нагрузка допустима!Цитата:
Сообщение от russtuff59
И уже из этой информации принимать решение! Но если исходить из того, что уже стоит корпуса ФИ, вам надо громкость! То значит в 2 Ома подключать!
pa d1000
вот нашел такую схемуВложение 1095418Цитата:
Сообщение от Dawa
ЧО за му-хрю!!! Где характеристики? К 7-й странице ждать?!?
---------- Сообщение добавлено 15.01.2017 в 22:22 ----------
долго искал...Цитата:
Сообщение от russtuff59
Это схема, как подключать те или иные катушки сабвуфера, что бы получить то или иное сопротивление!Цитата:
Сообщение от russtuff59
А вам надо инструкцию на ваш усилитель читать!
Pure Performance.Цитата:
Сообщение от mohov_a
Features like a continuously variable 12dB/octave low-pass crossover, switchable subsonic filter 24dB/octave, switchable 180° phase inversion. and a remote subwoofer level control function enable you to fine-tune your setup to optimize its performance in a variety of configurations.
PA500.4 Features:
125 Watts x 4 continuous, 200 x 4 dynamic power (2 ohm load), 4 channel mode.
250 Watts x 2 (4 ohm) continuous power, 2 channel mode.
CEA-2006 compliant specifications for true, accurate power ratings.
4-channel, dual bridge-mono (2-channel), or dual simultaneous stereo/mono operation provide a variety of configurations and setups: 4-channel for front and rear speakers; 2 speakers and a sub; 2 subwoofers; or 2 subs and 4-channels in passive-tri mode.
2 ohm stable 4-channel operation.
High-speed MOSFET switching power supply and high current bipolar output transistors pump maximum voltage and high current to your speakers or subwoofers.
Double layer fiberglass epoxy printed circuit boards for more rigidity, less shrinkage and a smaller overall amp footprint.
6-way Smart System Protection (SSP) circuits
Fully adjustable (50-500Hz) 12 dB/octave high- or low-pass crossover. Defeatable for full range (flat) operation.
Switchable 8 dB bass boost at 40Hz for extra bass thump.
Variable input gain optimizes match with different signal sources (250mv to 7.5V).
RCA outputs (front channels only) for easy daisy chaining of other amplifiers.
Mounting hardware with rubber isolation grommets and extra fuses included.
Light bar/fan output-Connect an optional LED light bar or cooling fan for custom installations.
Multi-color status LED gives instant information on amplifier operation.
Remote subwoofer level adjuster for rear channels included.
---------- Сообщение добавлено 16.01.2017 в 10:28 ----------
mohov_a, Pure Performance.
Features like a continuously variable 12dB/octave low-pass crossover, switchable subsonic filter 24dB/octave, switchable 180° phase inversion. and a remote subwoofer level control function enable you to fine-tune your setup to optimize its performance in a variety of configurations.
PA500.4 Features:
125 Watts x 4 continuous, 200 x 4 dynamic power (2 ohm load), 4 channel mode.
250 Watts x 2 (4 ohm) continuous power, 2 channel mode.
CEA-2006 compliant specifications for true, accurate power ratings.
4-channel, dual bridge-mono (2-channel), or dual simultaneous stereo/mono operation provide a variety of configurations and setups: 4-channel for front and rear speakers; 2 speakers and a sub; 2 subwoofers; or 2 subs and 4-channels in passive-tri mode.
2 ohm stable 4-channel operation.
High-speed MOSFET switching power supply and high current bipolar output transistors pump maximum voltage and high current to your speakers or subwoofers.
Double layer fiberglass epoxy printed circuit boards for more rigidity, less shrinkage and a smaller overall amp footprint.
6-way Smart System Protection (SSP) circuits
Fully adjustable (50-500Hz) 12 dB/octave high- or low-pass crossover. Defeatable for full range (flat) operation.
Switchable 8 dB bass boost at 40Hz for extra bass thump.
Variable input gain optimizes match with different signal sources (250mv to 7.5V).
RCA outputs (front channels only) for easy daisy chaining of other amplifiers.
Mounting hardware with rubber isolation grommets and extra fuses included.
Light bar/fan output-Connect an optional LED light bar or cooling fan for custom installations.
Multi-color status LED gives instant information on amplifier operation.
Remote subwoofer level adjuster for rear channels included.
я так понимаю 4-х канальник без сабсоника. Не советую 12-ки даже маломощные. А про оформление ФИ забыть без нормального усилителя.
зы не нужно мнго букф конкретно марку и модель усилителя укажите
Где тут моноблок?Цитата:
Сообщение от russtuff59
---------- Сообщение добавлено 16.01.2017 в 09:24 ----------
Утром глаза не протер? Советчик блин!Цитата:
Сообщение от mohov_a
Polk audio pa500.4Цитата:
Сообщение от mohov_a
