Helix xxl power

[Равилька]

Господа-товарищи! Нужна Ваша помощь! Собрал систему, а станция не запускается... мигает оранжевый индикатор, свидетельствующий о разрядке... Она должна как-то по особенному заряжаться?

---------- Сообщение добавлено 25.07.2016 в 07:55 ----------

Доброе утро! Прием!

---------- Сообщение добавлено 25.07.2016 в 18:23 ----------

Господа, подскажите куда капать дальше, без музыки тоска...

---

Полезные темы:

• [Chevrolet] Chevrolet Impala 1970
• Helix XXL Power Station
• Helix vs. Power Acoustic
• Helix XXL Power Station
• Helix XXL Competition BL

[jaff]

Привет. Нет, хитростей нет. Но есть кнопка ресет. Нужно попробовать обресетить.

[Равилька]

Привет. Нет, хитростей нет. Но есть кнопка ресет. Нужно попробовать обресетить.

Спасибо, что отозвались! На станции есть кнопка?

[jaff]

Спасибо, что отозвались! На станции есть кнопка?

http://narbi.free.fr/manuels/Amplis/...tation_XXL.pdf


15 Pushbutton to activate the system
After complete installation of the Power Station
(initial connection) and after connection of the battery
all devices connected to outputs 4, 5 and 6
must be charged carefully (including Caps without
protective electronics). To charge the system the
red button (15) must be pushed shortly. The white
LED (14) illuminates to indicate that the charging
is in progress. During the charging process all
connected devices must be switched off.
As soon as charging is completed the white LED
(14) and the yellow LED (11) go out. The system is
now ready for operation. If problems should occur
while charging (e.g. short circuit at the output,
plus minus were interchanged on a connected
device), the process can be interrupted with the
black pushbutton (16). If charging is not completed
after 10 minutes the process will be stopped
automatically.

16 Pushbutton to deactivate the systemAll connected devices (output 4, 5 and 6) can becarefully deactivated with the black button (16). Todischarge the system push the black button (16)shortly. To show that discharging is in progress theyellow LED (11) illuminates. After discharging iscompleted the yellow LED flashes.Necessary modifications on connected devicescan now be carried out. To modify the PowerStation itself remove the battery’s main fuse.

[Равилька]

http://narbi.free.fr/manuels/Amplis/...tation_XXL.pdf


15 Pushbutton to activate the system
After complete installation of the Power Station
(initial connection) and after connection of the battery
all devices connected to outputs 4, 5 and 6
must be charged carefully (including Caps without
protective electronics). To charge the system the
red button (15) must be pushed shortly. The white
LED (14) illuminates to indicate that the charging
is in progress. During the charging process all
connected devices must be switched off.
As soon as charging is completed the white LED
(14) and the yellow LED (11) go out. The system is
now ready for operation. If problems should occur
while charging (e.g. short circuit at the output,
plus minus were interchanged on a connected
device), the process can be interrupted with the
black pushbutton (16). If charging is not completed
after 10 minutes the process will be stopped
automatically.

16 Pushbutton to deactivate the systemAll connected devices (output 4, 5 and 6) can becarefully deactivated with the black button (16). Todischarge the system push the black button (16)shortly. To show that discharging is in progress theyellow LED (11) illuminates. After discharging iscompleted the yellow LED flashes.Necessary modifications on connected devicescan now be carried out. To modify the PowerStation itself remove the battery’s main fuse.

thank you. this is a very detailed and accurate information. immensely grateful for the prompt

[jaff]

Ршился вопрос ? ))

[Равилька]

Ршился вопрос ? ))

Запустился Теперь другие вопросы вылезли Можно задам?

[jaff]

Пиши конечно, полезная информация же останется.

[Равилька]

Пиши конечно, полезная информация же останется.

Написал в лс